iFLIGHT Cidora SL5 215mm 5 Inch 6S FPV Racing Drone With SucceX F7 50A Caddx Ratel 5.8G 1000mW VTX BNF - Frsky XM+ Receiver

General

Brand: iFLIGHT
Item Name: Cidora SL5
Version: BNF
Receiver: Frsky XM+ Receiver

Specification

Total Dimensions: 165*138mm (body dimension)
Weight: 384.2 (without GoPro TPU mount)
Frame Wheelbase: 215mm
Flight Control: SucceX F7 TwinG BlueTooth
ESC: SucceX 50A 2-6s 4-in-1 ESC Dshot1200
Motor: XING CAMO X2306 1700KV(6S)
Camera: Caddx Ratel 2.1mm Lens
Propeller: Nazgul 5140

SucceX F7 TwinG BT Flight Controller(TwinICM20689)

MCU: 216MHz STM32F722RET6 
Gyro: 2 x ICM20689(SPI)
Baro: Yes
Betaflight OSD: YES 
Bluetooth wireless adapter (Antenna integrated)
Blackbox: Onboard 32MB
5x Uarts
8x Motor outputs
8-pin 4in1 ESC port
4-pin VTX connector

Betaflight 
Betaflight Firmware: betaflight_4.0.5_STM32F7X2.hex
CLI dump file: IFLIGHTF7_TWIN_G.config

Physical 
Mounting hole: 30.5*30.5mm,φ4mm with Grommets φ3mm 
Size: 36*36mm 
Weight: 6.2g 

SucceX 50A 2-6S 4-in-1 ESC Dshot1200

Dimension: 43*39mm
Mounting Holes: 30.5*30.5mm/Φ3mm
Weight: 14.4g
Volts input: 2-6S
STM32F051 MCU, 48Mhz Runs BLHELI 32.X Firmware
Current sensor: Yes
Telemetry: Supported
BEC: No
Supports: DShot DShot150/300/600/1200/MultiShot/ OneShot etc.
Target: iFlight-BL32-4IN1
BLHeliSuite download (BL32)://www.mediafire.com/file/hkln8fcaif5s9l8/BLHeliSuite32_32616a.zip/file

5.8G 1000mW VTX

Support OSD Frequency and Power tuning;
The output power is stable, the far transmission distance: ≥10km
Transmit power 5 gear switch: 25mW/200mW/400mW/800mW/1000mW;
Output 48 frequency points, and has 6 group 8 race frequency at the same time using each other without interference;
Frequency lock fast, the boot does not interfere with companions;
Built-in output power self-check function;
Full format video format: NTSC /PAL;
Wide input voltage range. low power consumption:
7V-28V,+12V/500mA@1000mW;
Small size: 36mm×36mm×8mm;
Mounting holes 4-M3
Lightweight: ≤11g(excluding antenna)

Recommend Parts (Not included):

TPU 3D Printed Camera Mount for Gopro Hero 5/6/7 with ND8 Filter
TPU 3D Printed Camera Mount for GoPro Session

NOTE: The Hero 7 camera and TPU print camera mount are not included.

Weight & Dimensions

Package Weight: 0.755kg

Package Size (L x W x H): 23 x 22 x 6.6cm

Package Contents

1 x Cidora SL5 4S 6S FPV Drone - (BNF Version)
2 x Nazgul 5140 Propellers(set)
1 x LED Light(set)